Intranet
Language:

Products

SUBSTRUCTURE FOR STONE PRODUCTS Marble, granite, slate, limestone, sandstone ... PF-AL-T ARTICULADA
SUBSTRUCTURE FOR INDUSTRIALIZED PRODUCTS Stoneware, sintered ceramics, terracotta, asbestos cement, HPI, composites ...

PF-ALU/PL

Sistemas con sub-estrcutura de fachadas ventiladas - Sistema Masa PF-ALU/PL ARTICULADO
PF-ALU/PL CANAL/KNAUF PF-ALU-GR-PL-100 MEDIA PF-ALU-GR-PL-146 PF-ALU-GR-PL-100

Description

Fixed anchoring of a great capacity and resistance specifically designed to be mounted on PF-ALU aluminum profiles. The technique implemented in this type of anchoring features the use of a stamped double flat stainless steel bar and machined with adjustment bushings that are inserted in the single or continuous slotting carried out in the axis of the claddings to be installed. More specifically, the sizing and shaping of these anchors is done by double folding panels with a variable base. Each of these models is used depending on the dimensions of the cladding (thicknesses of 3, 4 and 5 cm) and of their position on the façade. The intersection GR-PL-100 model joins the cladding panels on the corners with the possibility of joining up to 4 panels. The GR-PL-46 model, on the other hand, only enables two panels to be connected.



Features

Technical specifications:
· Minimum wall cladding thickness: 30 mm.
· Recommended minimum joint:  6 mm horizontally and 3mm vertically.
· Machining: single slot.
· Calculations made with maximum densities up to 3000 kg/m3.

System designed to solve the fastening of claddings with horizontally positioned panels using two continuous joints (alternatively possible to use 50% locked joints in large panels). In addition, the PF-ALU/PL system can be used because it allows the installation of panels in a vertical position using locked joints.


Download Fact Sheet


Projects

PF-ALU/CER

Sistemas con sub-estrcutura de fachadas ventiladas - Sistema Masa PF-ALU/CER ARTICULADO
PF-ALU/CER CANAL PF-ALU-CER-GRAPA.46 PF-ALU-CER-GRAPA.100MEDIA PF-ALU-CER-GRAPA.100

Description

Anchor positioned parallel to the PF-ALU profile consisting of a single machined flat bar specifically designed for 5 to 25 thick claddings with panels that are frontally almost hidden because it can optionally be lacquered with the RAL color of the cladding to be supported. Highly versatile anchor that allows to easily reposition the cladding panels and/or replace them, always ensuring that the joint between the panels is mechanically kept stable. The system is equipped with a stainless steel spring and a bushing that maintain the cladding free from vibration and/or movement. It is available in two versions GR-PLC-46 and GR-PLC-100, depending on the size and the layout of the cladding to be supported.

Ideal to solve the fastening of claddings with horizontally positioned panels using two continuous joints in large panels. The PF-ALU/CER system also enables parts to be put into place with horizontal or vertical locked joints.



Features

Technical specifications:
· Minimum wall cladding thickness: 5 mm.  With a maximum thickness of 25 mm.
· Recommended minimum joint:  6 mm horizontally and 3mm vertically.
· No machining required (anchoring with visible flanges).
· Calculations made with maximum densities up to 3000 kg/m3.


Download Fact Sheet


Projects

PF-ALU/CLA

Sistemas con sub-estrcutura de fachadas ventiladas - Sistema Masa PF-ALU/CLA ARTICULADO
PF-ALU/CLA CANAL PF-ALU-CLA-VERTICAL PF-ALU-CLA-HORIZONTAL

Description

Parallel positioned anchoring of a great capacity and resistance, specifically designed to be mounted on PF-ALU aluminum profiles. The technique implemented in this type of anchoring features the use of a stamped and machined double flat stainless steel bar that allows adjusting the axis (x), supplementary to that of the profile, by means of a simple set of nut and lock nut in order to ensure proper vertical and horizontal alignment. Axis (y) is adjustable by means of the movement within its own position along the length of the profile, to which it is fixed with a self-tapping screw to prevent the clip from falling. Axis (z) allows a movement within its own position of up to 20 mm, supplementary to that of the fastening elements of the profiles.

This clip model is available in different sizes to better adapt to the specific characteristics of each cladding, load and wind conditions. System designed to solve the fastening of claddings with horizontally positioned panels using two continuous joints (alternatively possible to use 50% locked joints in large panels). Recommended for less compact material (for example: Sandstone)



Features

Technical specifications:
· Minimum wall cladding thickness: 30 mm. 
· Recommended minimum joint:    6 mm horizontally with free vertical movement
..Machining: Drill diameter 7.5 mm.
· Calculations made with maximum densities up to 3000 kg/m3.


Download Fact Sheet


Projects

PF-ALU/HPL

Sistemas con sub-estrcutura de fachadas ventiladas - Sistema Masa PF-ALU/HPL EMPOTRADO
PF-ALU/HPL CANAL PF-ALU.HPL-ESQUEMA1 PF-ALU.HPL-ESQUEMA2 PF-ALU.HPL-ESQUEMA3

Description

With this clip profile, Sistema Masa has excelled itself and any other product existing on the market given its great versatility and speed when being mounted, allowing the laying out of the vertical profiles at random, regardless of the position of the vertical joints of the cladding. The system's performance during assembly is exceptional because screws are not required to fasten the panels, ensuring the cladding's stability through an innovative design of the centering elements that offer the possibility of using different thicknesses in the vertical joints (1 mm to 10 mm) as it centers and favors the flatness of the cladding. It is specially recommended for smaller size cladding cut-offs in vertical position, with continuous horizontal joints or free vertical joints.



Features

Technical specifications:
· Minimum wall cladding thickness: 20 mm.
· Recommended minimum joint:   6 mm horizontally with free vertical movement
· Machining: with continuous slots, drills or visible flanges.
· Calculations made with maximum densities up to 3000 kg/m3.

System families PF-ALU/HPL
The horizontal profiles making up the PF-ALU/HPL system are marketed in 3 models: PF-ALU/HPL-40, PF-ALU/HPL-60 and PF-ALU/HPL-120 depending on the thickness, dimension and position of the cladding panels. These clip profiles are positioned parallel to the PF-ALU vertical profiles and the ES-ALU fastening elements in their three different versions, allowing preserving the system adjustment untouched.

With the increase of the KNAUF type WM.es lightweight cladding structures, to which good vertical and horizontal flatness is assumed, new calculation tables have been studied to be able to install the HPL clip profiles and anchor them directly to the cladding structure and in parallel to the KNAUF vertical structure (EXP. ITEC. QP-IT-4158-01.A).
 
PF-ALU/HPL-40
Ideal horizontal profile to fasten low (40/60 cm) panels. Its small dimensions allow the optimization of the separation between the PF-ALU profiles, making it more suitable for panels in horizontal position with continuous horizontal joints and free vertical joints and thicknesses ranging from 10 to 20 mm. Requires slot e: 2mm de-beaded.
 
PF-ALU/HPL-60
Horizontal profile with the greatest inertia dimensioned to house panels of an intermediate height of 60/100 cm. This is the most commonly used clip profile model, as it covers most of the normally studied off-cuts. It also provides greater flexibility, as it can be adapted correctly to small off-cuts without losing any competitivity, and to larger off-cuts without losing resistance. Requires slot e: 5.3 mm de-beaded. For thicknesses ranging from 20 to 50 mm.
 
PF-ALU/HPL-120
Horizontal profile with great inertia, especially designed to support large dimension pieces, preferably in vertical position, with continuous horizontal and free vertical joint.
Requires slot e: 5,3 mm de-beaded (idem PF-ALU/HPL-60).


Download Fact Sheet


Projects

PF-ALU/HTR

Sistemas con sub-estrcutura de fachadas ventiladas - Sistema Masa PF-ALU/HTR EMPOTRADO
PF-ALU/HTR CANAL PF-ALU.HRT-ESQUEMA1 PF-ALU.HRT-ESQUEMA2

Description

Horizontal profile PF-ALU-HTR, continuous support of upper and lower GR-TR anchoring, fixed to the vertical profile PF-ALU with self-tapping screws, with the function of supporting the weight of the cladding and wind load. The GR-TR anchor, specially designed for varying cladding thicknesses, is fixed to the cladding panels by means of the TR-MASA plug, designed for porcelain claddings and/or stone claddings featuring a remarkable compressive strength. The technique implemented in this system features the use of an extruded aluminum anchoring, machined by specific geometry in order to fit in the horizontal profile, with height adjustment and fixed to the cladding by inserting the TR-MASA plug in the cylindrical holes made on the rear side of the panels to make up the cladding. As also applicable to other Sistema Masa products, it allows easy assembly with the possibility of replacing or installing panels at any point of the cladding.

System designed to solve the fastening of thin claddings, especially for slate/phyllite panels due to their high level of exfoliation. System designed to solve the fastening of claddings with vertically positioned panels with continuous horizontal joints or free vertical joints. Recommended for compact material (i.e.: Granite, Basalt, etc.).



Features

Technical specifications:
· Minimum wall cladding thickness: 10 mm.
· Recommended minimum joint:  9 mm horizontally and 3 mm vertically.
· Machining: drill calibrated by backfilling the parts
· Calculations made with maximum densities up to 3000 kg/m3.

System families PF-ALU/HTR
The horizontal profiles making up the PF-ALU/HTR system are
marketed in 3 models: PF-ALU/HTR-40, PF-ALU/HTR-60 and PF-ALU/HTR-120 depending on the thickness, dimension and position of the cladding panels. These clip profiles are positioned parallel to the PF-ALU vertical profiles and the ES-ALU fastening elements in their three different versions, allowing preserving the system adjustment untouched.

With the increase of the KNAUF type WM.es lightweight cladding structures, to which good vertical and horizontal flatness is assumed, new calculation tables have been studied to be able to install the HTR clip profiles and anchor them directly to the cladding structure and in parallel to the KNAUF vertical structure (EXP. ITEC. QP-IT-4158-01.A)
 
PF-ALU-HTR-40
Ideal horizontal profile to fasten low (40/60 cm) panels. Its small dimensions allow the optimization of the separation between the PF-ALU profiles, making it more suitable for panels in horizontal position with continuous horizontal joints and free vertical joints and thicknesses ranging from 10 to 20 mm. Requires calibrated drill at the rear side of the panel.
 
PF-ALU-HTR-60
Horizontal profile with the greatest inertia dimensioned to house panels of an intermediate height of 60/100 cm. This is the most commonly used clip profile model, as it covers most of the normally studied off-cuts. It also provides greater flexibility, as it can be adapted correctly to small off-cuts without losing any competitivity, and to larger off-cuts without losing resistance. For thicknesses ranging from 20 to 50 mm.
Requires calibrated drill at the rear side of the panel.
 
PF-ALU-HTR-120
Horizontal profile with great inertia, especially designed to support large dimension pieces, preferably in vertical position, with continuous horizontal and free vertical joint. Requires calibrated drill at the rear side of the panel.


Download Fact Sheet


Projects

PF-ALT/SO

PF-ALT/SO ARTICULADO PF-ALT/SO EMPOTRADO
PF-ALT/SO CANAL PF-AL-T.SO INTERMEDIO O EXTREMO PF-AL-T.SO MATAJUNTA PF-AL-T.SO EN JUNTA

Description

ACompletely hidden anchoring, which is positioned parallel to the vertical uprights and is especially designed for thin claddings, in particular porcelain stoneware. The whole system is applied with high specification adhesive in order to guarantee correct fastening with the highest level of safety. The system is easy to be applied and requires an e:1 mm machining on the edge of the cladding panels in order to house the anchoring flanges. There are two versions available, Pin and Terminal, depending on the area of cladding to be fastened.

Especially suitable for claddings with horizontally positioned panels using two continuous joints (alternatively possible to use 50% locked joints).



Features

Technical specifications
· Minimum wall cladding thickness: 8 mm.  (provided that it can be machined)
  Maximum thickness of 15 mm.
· Recommended minimum joint: 7 mm.  horizontally, 3 mm vertically.
· Machining: slot e: 1.5 mm.
· Calculations made with maximum densities up to 3000 kg/m3.

The GR-SO anchor is placed on the vertical profile in any of the PF-AL-T, L, J, TT, JT, T35 and J35 models centered on the base profile, allowing a right and left shift of 20 mm due to its larger size and its lateral flanges on the 100 Pin model and 10 mm on the 46 Terminal model, favoring the centering of the cladding panel and avoiding any imbalance in the distribution of weights.

The connection to the vertical profile is made with a drill bit screw with an extra-flat head DIN 7504 4.2 x 12.7 made from stainless steel. A2/A4.

Multi-purpose elastic adhesive putty based on mono-component polyurethane with a medium to high curing module with atmospheric humidity. The application method is very simple, using cords in the vertical profile, requiring a primer or bonding bridge prior to application for correct adhesion to the profile and later to the porcelain stoneware.
 


Download Fact Sheet


Projects

PF-ALT/SV

PF-AL-T.SV-ARTICULADO PF-AL-T.SV-EMPOTRADO
PF-AL-T.SV-CANAL PF-AL-T.SV INTERMEDIO O EXTREMO PF-AL-T.SV MATAJUNTA PF-AL-T.SV EN JUNTA

Description

Anchoring with visible flanges which is positioned parallel to the vertical uprights and is especially designed for porcelain stoneware claddings. The system works in conjunction with a multi-purpose elastic adhesive putty based on polyurethane to guarantee correct fastening with the highest level of safety, together with GR-SV-100 or 46 mechanical anchor pins and terminals. Easy to apply, the system does not require machining on the panels, the anchor’s flange is exposed and there is the option of being able to finish it in the RAL color most similar to the cladding.

There are two versions available, Pin and Terminal, depending on the area of cladding to be fastened.

Especially suitable for claddings with horizontally and/or vertically positioned panels using two continuous joints, alternatively possible to use 50% locked joints.



Features

Technical specifications:
· Minimum wall cladding thickness: 9 mm. Maximum thickness of 20 mm.
· Recommended minimum joint: 7 mm horizontally and 3 mm vertically.
· The system requires no machining
· Calculations made with maximum densities up to 3000 kg/m3.

Multi-purpose elastic adhesive putty based on mono-component polyurethane with a medium to high curing module with atmospheric humidity. The application method is very simple, using cords in the vertical profile, requiring a primer or bonding bridge prior to application for correct adhesion to the profile and later to the porcelain stoneware.


Download Fact Sheet


Projects

PF-AL/TH FRONTAL PF-AL/TH EMPOTRADO
PF-AL/TH CANAL PF-AL/TH FRONTAL PF-AL/TH FRONTAL PF-AL/TH TYPOLOGY 46 PF-AL/TH TYPOLOGY 100 PF-AL/TH SCHEMATIC JOINT HORIZONTAL PF-AL/TH SCHEMATIC JOINT VERTICAL

Description

Horizontal profile PF-AL/TH, continuous support supplemented with GR-SV and GR-SO-S anchors, depending on whether the anchoring is visible or hidden, fixed to the vertical profiles PF-AL-L/J with self-tapping bolts, with the function of supporting the weight of the cladding and wind load. The PF-AL/TH profiling, especially designed for horizontal light claddings with free vertical joints or in vertical position, both in large format.

As also applicable to other Sistema Masa products, it allows easy assembly with the possibility of replacing or installing panels at any point of the cladding.

System designed to solve the fastening of thin and large format claddings, such as sintered ceramic elements, fiber-cement, composites, glass, HPL, etc. The system is applied with high specification adhesive and is equipped with the above described anchors.



Features

PF-AL/THP
Intermediate horizontal profile located on horizontal joints at the intersection of two panels, upper and lower. Allows the placement of mechanical anchors, structural adhesive, and thanks to its specific channel, it also allows the placement of the Masa key.
 
PF-AL/THT
Terminal horizontal profile located at the start and end of the cladding, or in the case of large-format vertical cut-offs, in the intermediate areas. Allows the placement of mechanical anchors, structural adhesive, and thanks to its specific channel, it also allows the placement of the Masa key.
 
Sistema Masa has designed an innovative system of keys that press the cladding against the profile and maintain the joint between panels, retracting once the adhesive has reached its optimum load state.


Download Fact Sheet


Projects

PF-ALT/SO-S

PF-ALT/SO-S ARTICULADO PF-ALT/SO-S DETALLE LLAVE
PISTOLA BOSTIK FOAMTAPE PF-ALT/SO-S ESQUEMA DISCONTINUO PF-ALT/SO-S ESQUEMA CONTINUO PF-ALT/SO-S TIPOLOGIA 100 PF-ALT/SO-S TIPOLOGIA 46 MATAJUNTAS PF-ALT/SO-S TIPOLOGIA 46 PF-ALT/SO-S LLAVE PF-ALT/SO-S EMPOTRADO PF-ALT/SO-S PROCESO 4 PF-ALT/SO-S PROCESO 3 PF-ALT/SO-S PROCESO 2 PF-ALT/SO-S PROCESO 1 PF-ALT/SO-S PF-ALT/SO-S PF-ALT/SO-S CANAL

Description

Completely hidden anchoring, which consists of vertical uprights of different types and especially designed for large format thin claddings of small thickness, such as sintered ceramic elements, fiber-cement, composites, glass, HPL, etc. The whole system is applied with high specification adhesive and is equipped with GR-SO-S support anchors and double sided tapes in order to guarantee correct and long-life fastening with the highest level of safety. It is also worth mentioning the use of the Masa keys patented and designed to ensure the perfect position of the panels and the joints between them, keeping the flatness of the cladding in contact with the tape and the adhesive to obtain the optimal degree of functionality. They are subsequently removed and/or reused.

The PF-AL-T/TT/T35 system is designed for large formats arranged horizontally; for architectural designs with vertical panel layout, there is a variant of the system that is complemented with horizontal profiles called PF-AL-TH with the same operation and GR-SO-S support anchors described (see corresponding sheet).



Features

Technical specifications:
· Minimum cladding thickness: 3 mm. Maximum thickness of 15 mm.
· Recommended minimum joint:   3 mm horizontally and 3 mm vertically.
· The system requires no machining
· Calculations made with maximum densities up to 3000 kg/m3.

The GR-SO-S anchor is placed on the vertical profile on any of the PF-AL-T, L, J, TT, JT, T35 and J35 models centered on the base profile. The connection to the vertical profile is made with a drill bit screw with an extra-flat head DIN 7504 4,2 x 12,7 made from stainless steel. A2/A4.

The double-sided adhesive tape, 3 mm thick and 12 mm wide, helps the initial fastening of the panel and ensures sufficient thickness of the adhesive applied.

Sistema Masa has designed an innovative system of keys that press the cladding against the profile and maintain the joint between panels, retracting once the adhesive has reached its optimum load state.


Download Fact Sheet


Projects

PF-AL-T/SO-S/R45

GR-SO-R45-TSE GR-SO-R45

Description

Completely hidden anchoring, which consists of vertical uprights of different types and especially designed for large format thin claddings of small thickness, such as sintered ceramic elements, fiber-cement, composites, glass, HPL, etc. The whole system is applied with high specification adhesive and is equipped with GR-SO-S support anchors, rollover restraint element GR-SO-45 and double sided tapes in order to guarantee correct and long-life fastening with the highest level of safety. It is also worth mentioning the use of the Masa keys patented and designed to ensure the perfect position of the panels and the joints between them, keeping the flatness of the cladding in contact with the tape and the adhesive to obtain the optimal degree of functionality. They are subsequently removed and/or reused.
The PF-AL-T/TT/T35 system is designed for large formats arranged horizontally; for architectural designs with vertical panel layout, there is a variant of the system that is complemented with horizontal profiles called PF-AL-TH.



Features

· Minimum wall cladding thickness: 3 mm. Maximum thickness of 15 mm.
· Recommended minimum joint:  3 mm horizontally and 3 mm vertically.
· Calculations made with maximum densities up to 3000 kg/m3.
· Single slot at the rear side at 45º.



Download Fact Sheet


Projects